OVHcloud Network Status

Current status
Legend
  • Operational
  • Degraded performance
  • Partial Outage
  • Major Outage
  • Under maintenance
FS#5086 — rbx-97-n7
Scheduled Maintenance Report for Network & Infrastructure
Completed
A bug on the actual version of NX-OS of rbx-97-n7
prevent us from recording the configuration on the
cards. It is a known bug which is fixed in the
following version.

We will do a switchover of sup card, i.e,
switch from the sup 1 to the sup 2 in order to be able to
record the configuration. This switchover
is made on the spot and there would be no problem.

Then, we will update the NX-OS. This
operation is also made on the spot since the N7 is
ISSU.

Update(s):

Date: 2011-02-01 15:13:26 UTC
Mod Sw Hw
--- -------------- ------
1 5.1(2) 1.0
2 5.1(2) 1.0
3 5.1(2) 1.7
4 5.1(2) 1.0
5 5.1(2) 1.0
9 5.1(2) 1.6
10 5.1(2) 1.6


Date: 2011-02-01 15:13:17 UTC
The maps have been updated.
Reload on 9 was a little too fast. Card 10 has not booted to the end. There was a power cut on the storage of NAS, iSCSI and backup SDN.

Date: 2011-02-01 15:12:21 UTC
rbx-97-n7# reload module 10
This command will reboot standby supervisor module. (y/n)? [n] y
about to reset standby sup
2011 Feb 1 15:27:57 rbx-97-n7 %PLATFORM-2-PFM_MODULE_RESET: Manual restart of Module 10 from Command Line Interface
rbx-97-n7# 2011 Feb 1 15:28:00 rbx-97-n7 %PLATFORM-2-MOD_REMOVE: Module 10 removed (Serial number )

Date: 2011-02-01 15:12:08 UTC
The maps have been updated.

We will now restart the supervisor card.

Date: 2011-02-01 15:10:11 UTC
2011 Feb 1 14:04:49 rbx-97-n7 %$ VDC-1 %$ Feb 1 14:04:49 %KERN-2-SYSTEM_MSG: Switchover started by redundancy driver - kernel
2011 Feb 1 14:04:49 rbx-97-n7 %$ VDC-1 %$ %SYSMGR-2-HASWITCHOVER_PRE_START: This supervisor is becoming active (pre-start phase).
2011 Feb 1 14:04:49 rbx-97-n7 %$ VDC-1 %$ %SYSMGR-2-HASWITCHOVER_START: Supervisor 9 is becoming active.
2011 Feb 1 14:04:51 rbx-97-n7 %$ VDC-1 %$ %SYSMGR-2-SWITCHOVER_OVER: Switchover completed.
2011 Feb 1 14:04:52 rbx-97-n7-interne %$ VDC-3 %$ %STP-2-VPC_PEERSWITCH_CONFIG_DISABLED: vPC peer-switch configuration is disabled. Please make sure to change spanning tree \"bridge\" priority as per the recommended guidelines.
2011 Feb 1 14:10:27 rbx-97-n7 %$ VDC-1 %$ %CMPPROXY-STANDBY-2-LOG_CMP_UP: Connectivity Management processor(on module 10) is now UP

Date: 2011-02-01 15:10:01 UTC
Here we go.

Date: 2011-02-01 15:09:35 UTC
2011 Feb 1 14:01:09 rbx-97-n7 %$ VDC-1 %$ %CMPPROXY-STANDBY-2-LOG_CMP_UP: Connectivity Management processor(on module 9) is now UP

Date: 2011-02-01 15:09:25 UTC
--More--2011 Feb 1 13:55:23 rbx-97-n7 %$ VDC-1 %$ %PLATFORM-2-MOD_REMOVE: Module 9 removed (Serial number )

Date: 2011-02-01 15:09:17 UTC
Compatibility check is done:
Module bootable Impact Install-type Reason
------ -------- -------------- ------------ ------
1 yes non-disruptive rolling
2 yes non-disruptive rolling
3 yes non-disruptive rolling
4 yes non-disruptive rolling
5 yes non-disruptive rolling
9 yes non-disruptive reset
10 yes non-disruptive reset



Images will be upgraded according to following table:
Module Image Running-Version(pri:alt) New-Version Upg-Required
------ ---------- ---------------------------------------- -------------------- ------------
1 lc1n7k 5.1(1) 5.1(2) yes
1 lc1n7k 5.1(1) 5.1(2) yes
1 bios v1.10.14(04/02/10): v1.10.14(04/02/10) v1.10.14(04/02/10) no
2 lc1n7k 5.1(1) 5.1(2) yes
2 lc1n7k 5.1(1) 5.1(2) yes
2 bios v1.10.14(04/02/10): v1.10.14(04/02/10) v1.10.14(04/02/10) no
3 lc1n7k 5.1(1) 5.1(2) yes
3 lc1n7k 5.1(1) 5.1(2) yes
3 bios v1.10.14(04/02/10): v1.10.14(04/02/10) v1.10.14(04/02/10) no
4 lc-d-n7k 5.1(1) 5.1(2) yes
4 lc-d-n7k 5.1(1) 5.1(2) yes
4 bios v1.10.13(03/15/10): v1.10.13(03/15/10) v1.10.14(04/02/10) yes
5 lc-d-n7k 5.1(1) 5.1(2) yes
5 lc-d-n7k 5.1(1) 5.1(2) yes
5 bios v1.10.13(03/15/10): v1.10.13(03/15/10) v1.10.14(04/02/10) yes
9 system 5.1(1) 5.1(2) yes
9 kickstart 5.1(1) 5.1(2) yes
9 bios v3.22.0(02/20/10): v3.22.0(02/20/10) v3.22.0(02/20/10) no
9 cmp 5.1(1) 5.1(1) no
9 cmp-bios 02.01.05 02.01.05 no
10 system 5.1(1) 5.1(2) yes
10 kickstart 5.1(1) 5.1(2) yes
10 bios v3.22.0(02/20/10): v3.22.0(02/20/10) v3.22.0(02/20/10) no
10 cmp 5.1(1) 5.1(1) no
10 cmp-bios 02.01.05 02.01.05 no

Date: 2011-02-01 15:09:03 UTC
Here we go.

Date: 2011-01-31 12:36:09 UTC
Everything is up. There has been no cut off.
The configuration is recorded.

We will prepare the updating.

Date: 2011-01-31 12:33:24 UTC
2011 Jan 31 12:19:24 rbx-97-n7 %$ VDC-1 %$ %USER-2-SYSTEM_MSG: clis_nvdb_update_thread: unable to open startup pss file nonvolatile:/var/sysmgr/startup-cfg/vdc_3/bin/clis_startup_config, rc = 0x80480002 - clis

Date: 2011-01-31 12:33:10 UTC
NX7 SUP Ver 3.22.0
Serial Port Parameters from CMOS
PMCON_1: 0x200
PMCON_2: 0x0
PMCON_3: 0x3a
PM1_STS: 0x101
Performing Memory Detection and Testing
Total mem found : 4096 MB
Performing memory test... Passed.
NumCpus = 2.
Status 61: PCI DEVICES Enumeration Started
Status 62: PCI DEVICES Enumeration Ended
Status 9F: Dispatching Drivers
Status 9E: IOFPGA Found
Status 9A: Booting From Primary ROM
Status 98: Found Cisco IDE
Status 98: Found Cisco IDE
Status 90: Loading Boot Loader

Reset Reason Registers: 0x1 0x0
Filesystem type is ext2fs, partition type 0x83


GNU GRUB version 0.97

Autobooting bootflash:/n7000-s1-kickstart.5.1.1.bin bootflash:/n7000-s1-dk9.5.1
.1.bin...
Filesystem type is ext2fs, partition type 0x83
Booting kickstart image: bootflash:/n7000-s1-kickstart.5.1.1.bin....
...............................................................................
....................Image verification OK

INIT: version 2
Checking all filesystems..r.r.r..r done.
Loading system software
/bootflash//n7000-s1-dk9.5.1.1.bin read done
Uncompressing system image: bootflash:/n7000-s1-dk9.5.1.1.bin Mon Jan 31 12:13:59 CET 2011
blogger: nothing to do.

..done Mon Jan 31 12:14:02 CET 2011
Load plugins that defined in image conf: /isan/plugin_img/img.conf
Loading plugin 0: core_plugin...
num srgs 1
0: swid-core-supdc3, swid-core-supdc3
num srgs 1
0: swid-supdc3-ks, swid-supdc3-ks
INIT: Entering runlevel: 3


rbx-97-n7# 2011 Jan 31 12:15:10 rbx-97-n7 %$ VDC-1 %$ %CMPPROXY-STANDBY-2-LOG_CMP_UP: Connectivity Management processor(on module 9) is now UP


Date: 2011-01-31 12:32:49 UTC
rbx-97-n7# reload module 9
WARNING: . So, reload is not recommended
!!!WARNING! there is unsaved configuration!!!
This command will cause supervisor switchover (y/n)? [n] y
about to reset active sup
2011 Jan 31 12:09:45 rbx-97-n7 %$ VDC-1 %$ %PLATFORM-2-PFM_MODULE_RESET: Manual restart of Module 9 from Command Line Interface

writing reset reason 9,

rbx-97-n7(standby)# 2011 Jan 31 12:09:50 rbx-97-n7 %$ VDC-1 %$ %SYSMGR-2-HASWITCHOVER_PRE_START: This supervisor is becoming active (pre-start phase).
2011 Jan 31 12:09:50 rbx-97-n7 %$ VDC-1 %$ %SYSMGR-2-HASWITCHOVER_START: Supervisor 10 is becoming active.
2011 Jan 31 12:09:52 rbx-97-n7 %$ VDC-1 %$ %SYSMGR-2-SWITCHOVER_OVER: Switchover completed.
2011 Jan 31 12:09:55 rbx-97-n7-interne %$ VDC-3 %$ %STP-2-VPC_PEERSWITCH_CONFIG_DISABLED: vPC peer-switch configuration is disabled. Please make sure to change spanning tree \"bridge\" priority as per the recommended guidelines.

rbx-97-n7# 2011 Jan 31 12:09:56 rbx-97-n7 %$ VDC-1 %$ %CALLHOME-2-EVENT: SUP_FAILURE

Date: 2011-01-31 12:32:32 UTC
Well, it is being complicated.

rbx-97-n7# system switchover
Failed to switch over (update of startup configuration in progress)

Date: 2011-01-31 12:31:28 UTC
rbx-97-n7# sh system redundancy ha ?
status Current vdc redundancy status

rbx-97-n7# sh system redundancy ha status
VDC No This supervisor Other supervisor
------ --------------- ---------------

vdc 1 Active with HA standby HA standby
vdc 2 Active with HA standby HA standby
vdc 3 Active with HA standby HA standby
vdc 4 Active with HA standby HA standby
rbx-97-n7# sh system redundancy status
Redundancy mode
---------------
administrative: HA
operational: HA

This supervisor (sup-1)
-----------------------
Redundancy state: Active
Supervisor state: Active
Internal state: Active with HA standby

Other supervisor (sup-2)
------------------------
Redundancy state: Standby
Supervisor state: HA standby
Internal state: HA standby
rbx-97-n7#
Posted Jan 31, 2011 - 12:31 UTC